Automated Failure testing

Automated Failure Testing works by inserting a network proxy (mitmproxy) between the Citus coordinator and one of the workers (connections to the other worker are left unchanged). The proxy is configurable, and sits on a fifo waiting for commands. When it receives a command over the fifo it reconfigures itself and sends back response. Regression tests which use automated failure testing communicate with mitmproxy by running special UDFs which talk to said fifo. The tests send commands such as "fail any connection which contain the string COMMIT" and then run SQL queries and assert that the coordinator has reasonable behavior when the specified failures occur.

Table of Contents

Getting Started

First off, to use this you'll need mitmproxy, I recommend version 3.0.4, and I also recommend running it with python 3.6. This script integrates pretty deeply with mitmproxy so other versions might fail to work.

I highly recommend using pipenv to install mitmproxy. It lets you easily manage isolated environments (instead of installing python packages globally). If you've heard of virtualenv, pipenv is that but much easier to use.

Once you've installed it:

bash $ cd src/test/regress $ pipenv --python 3.6 $ pipenv install # there's already a Pipfile.lock in src/test/regress with packages $ pipenv shell # this enters the virtual environment, putting mitmproxy onto $PATH

That's all you need to do to run the failure tests:

bash $ make check-failure

Running mitmproxy manually

bash $ mkfifo /tmp/mitm.fifo # first, you need a fifo $ cd src/test/regress $ pipenv shell $ mitmdump --rawtcp -p 9702 --mode reverse:localhost:9700 -s mitmscripts/fluent.py --set fifo=/tmp/mitm.fifo

The specific port numbers will be different depending on your setup. The above string means mitmdump will accept connections on port 9702 and forward them to the worker listening on port 9700.

Now, open psql and run:

```psql

UPDATE pg_dist_node SET nodeport = 9702 WHERE nodeport = 9700;

```

Again, the specific port numbers depend on your setup.

Using Failure Test Helpers

In a psql front-end run ```psql

\i src/test/regress/sql/failure_test_helpers.sql

```

The above file creates some UDFs and also disables a few citus features which make connections in the background.

You also want to tell the UDFs how to talk to mitmproxy (careful, this must be an absolute path):

```psql

SET citus.mitmfifo = '/tmp/mitm.fifo';

```

(nb: this GUC does not appear in shared_library_init.c, Postgres allows setting and reading GUCs which have not been defined by any extension)

You're all ready! If it worked, you should be able to run this:

```psql

SELECT citus.mitmproxy('conn.allow()');

mitmproxy

(1 row) ```

citus.mitmproxy() command strings

Command strings specify a pipline. Each connection is handled individually, and the pipeline is called once for every packet which is sent. For example, given this string:

conn.onQuery().after(2).kill() -> kill a connection if three Query packets are seen

  • onQuery() is a filter. It only passes Query packets (packets which the frontend sends to the backend which specify a query which is to be run) onto the next step of the pipeline.

  • after(2) is another filter, it ignores the first two packets which are sent to it, then sends the following packets to the next step of the pipeline.

  • kill() is an action, when a packet reaches it the connection containing that packet will be killed.

Actions

There are 5 actions you can take on connections:

| Action | Description | |:--------------------|:---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------| | conn.allow() | the default, allows all connections to execute unmodified | | conn.kill() | kills all connections immediately after the first packet is sent | | conn.reset() | kill() calls shutdown(SHUT_WR), shutdown(SHUT_RD), close(). This is a very graceful way to close the socket. reset() causes a RST packet to be sent and forces the connection closed in something more resembling an error. | | conn.cancel(pid) | This doesn't cause any changes at the network level. Instead it sends a SIGINT to pid and introduces a short delay, with hopes that the signal will be received before the delay ends. You can use it to write cancellation tests. | | conn.killall() | the killall() command kills this and all subsequent connections. Any packets sent once it triggers will have their connections killed. |

The first 4 actions all work on a per-connection basis. Meaning, each connection is tracked individually. A command such as conn.onQuery().kill() will only kill the connection on which the Query packet was seen. A command such as conn.onQuery().after(2).kill() will never trigger if each Query is sent on a different connection, even if you send dozens of Query packets.

Filters

  • conn.onQuery().kill()
    • kill a connection once a Query packet is seen
  • conn.onCopyData().kill()
    • kill a connection once a CopyData packet is seen

The list of supported packets can be found in structs.py, and the list of packets which could be supported can be found here

You can also inspect the contents of packets:

  • conn.onQuery(query="COMMIT").kill()
    • You can look into the actual query which is sent and match on its contents.
    • Note that this is always a regex
  • conn.onQuery(query="^COMMIT").kill()
    • The query must start with COMMIT
  • conn.onQuery(query="pg_table_size\(")
    • You must escape parens, since you're in a regex
  • after(n)
    • Matches after the n-th packet has been sent:
  • conn.after(2).kill()
    • Kill connections when the third packet is sent down them

There's also a low-level filter which runs a regex against the raw content of the packet:

  • conn.matches(b"^Q").kill()
    • This is another way of writing conn.onQuery()
    • Note the b, it's always required.

Chaining

Filters and actions can be arbitrarily chained:

  • conn.matches(b"^Q").after(2).kill()
    • kill any connection when the third Query is sent

Recording Network Traffic

There are also some special commands. This proxy also records every packet and lets you inspect them:

  • recorder.dump()
    • Emits a list of captured packets in COPY text format
  • recorder.reset()
    • Empties the data structure containing the captured packets

Both of those calls empty the structure containing the packets, a call to dump() will only return the packets which were captured since the last call to dump() or reset()

Back when you called \i sql/failure_test_helpers.sql you created some UDFs which make using these strings easier. Here are some commands you can run from psql, or from inside failure tests:

  • citus.clear_network_traffic()
    • Empties the buffer containing captured packets
  • citus.dump_network_traffic()
    • Returns a little table and pretty-prints information on all the packets captured since the last call to clear_network_traffic() or dump_network_traffic()